Airbrush Introduction: Difference between revisions

Latest revision as of 23:21, 19 May 2024

This is the content required for an introduction to our airbrush equipment . Reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

If you need this introduction, please reach out to the following tutors: Björn

Health & Safety Precautions

Personal protection:

Wear goggles and gloves if you use solvent-based paint. Gloves are also required if you airbrush something you are holding/touching!

Hearing protection is also recommended due to the noise of the fume extractor directly overhead.


Danger	Description	Precautions
Aerosols	Airbrushing creates aerosols/vapours. Solvent-based AND water-based paint can cause pneumonia and other long-term lung problems. Paint particles might travel away from the airbrush area and harm other equipment or people.	use spray booth air extractor AND a respirator close the curtain behind you water-based colours: wear a mask with "P2" or even better "P3" filters when working with solvent-based colours: wear goggles and a mask with "A2" grade filters to protect against the solvent fumes these "gas and vapour cartridges" have a use-by date and need to be replaced from time to time (according to the manufacturer's recommendations) do not do any face painting
Paint	some paints may contain substances that are harmful to your skin	wear gloves (single use latex/nitrile gloves or reusable painting gloves/Lackierhandschuhe) if you are holding or touching your medium during the project
Airbrush Needle	every airbrush has a needle inside which is usually covered/protected, but will become accessible when you disassemble the airbrush for cleaning	handle with care never "poke" the front of the needle
Compressor	compressed air is generated and released through the airbrush the airstream can damage eyes, ears and other sensible organs	do not point the airbrush at yourself or other people
Spray Booth	the adjustable metal plate may bruise your fingers when reverted back to its vertical position	grab the metal plate on the left/right side, NOT underneath

Practical Demonstration

The tutor will show you these steps in detail:

airbrush and needle functionality (before connecting airbrush to compressor!)
how to connect an airbrush to the compressor
change compressor pressure settings
add paint/change paint
how "thin" or "watery" the paint needs to be
turn on the fume hood
spray examples with varying needle positions (fine line / area fill etc)
disconnect the airbrush from the compressor
disassemble airbrush
clean airbrush
reassemble & store airbrush

@@ Line 1: / Line 1: @@
-{{incomplete}}
+This is the content required for an introduction to our [[Introduction for::Airbrush Compressor|airbrush equipment]] . '''Reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+If you need this introduction, please reach out to the following tutors: [[Tutor::User:Björn|Björn]]
+== Health & Safety Precautions ==
+[[PPE|Personal protection]]: [[File:Protection - breathing.svg|50px]]
-This is the content required for an introduction to our [[Introduction for::Airbrush Compressor|airbrush equipment]] . '''Reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+Wear [[goggles]] and [[gloves]] if you use solvent-based paint. Gloves are also required if you airbrush something you are holding/touching!
-If you need this introduction, please reach out to the following tutors:
+[[Hearing Protection|Hearing protection]] is also recommended due to the noise of the fume extractor directly overhead.
-===Health & Safety Precautions===
+{| class="wikitable"
-[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]] [[File:Protection - hearing.svg|50px]] [[File:Protection - gloves.svg|50px]]
-{| class="wikitable"
 |+
 !Danger
@@ Line 13: / Line 16: @@
 !Precautions
 |-
 |Aerosols
-|Airbrushing creates aerosols / vapours. Solvent-based AND water-based can cause pneumonia and other long-term lung problems.
+|
+*Airbrushing creates aerosols/vapours. Solvent-based AND water-based paint can cause pneumonia and other long-term lung problems.
+*Paint particles might travel away from the airbrush area and harm other equipment or people.
 |
 *use spray booth air extractor AND a respirator
+*close the curtain behind you
 *water-based colours: wear a mask with "P2" or even better "P3" filters when working with
-*solvent-based colours: wear a mask with "A2" grade filters to protect against the solvent fumes.
+*solvent-based colours: wear [[goggles]] and a mask with "A2" grade filters to protect against the solvent fumes
-** These "gas and vapour cartridges" have a use-by date and need to be replaced from time to time  (according to the manufacturer's recommendations).
+** these "gas and vapour cartridges" have a use-by date and need to be replaced from time to time  (according to the manufacturer's recommendations)
-* wear goggles
 * do not do any face painting
 |-
@@ Line 26: / Line 31: @@
 |some paints may contain substances that are harmful to your skin
 |
-* wear gloves
+* wear gloves (single use latex/nitrile gloves or reusable painting gloves/''Lackierhandschuhe'') if you are holding or touching your medium during the project
 |-
-|Airbrush needle
+|Airbrush Needle
-|Every airbrush gun has a needle inside. The needle is usually covered/protected, but will become accessible when you disassemble the airbrush for cleaning.
+|every airbrush has a needle inside which is usually covered/protected, but will become accessible when you disassemble the airbrush for cleaning
 |
 *handle with care
@@ Line 35: / Line 40: @@
 |-
 |Compressor
-| compressed air is generated and released through the airbrush:
+| compressed air is generated and released through the airbrush
 *the airstream can damage eyes, ears and other sensible organs
 |
 *do not point the airbrush at yourself or other people
-|-
-|Noise
-|Noise from the air extractor (the compressor is relatively quiet, and turns itself on/off depending on air pressure settings)
-|
-* Noise protection gear
 |-
 |Spray Booth
-|The adjustable metal plate may bruise your fingers when reverted back to its vertical position.
+|the adjustable metal plate may bruise your fingers when reverted back to its vertical position
-|
-* Grab the metal plate on the left/right side, NOT underneath.
-|-
-|Paint fumes
-|Paint aerosols might travel away from the airbrush corner and cause damage to other equipment.
 |
-*use spray booth with extractor
+* grab the metal plate on the left/right side, NOT underneath
-*close the curtain behind you
 |}
-=== Practical Demonstration===
+== Practical Demonstration ==
-*show airbrush and needle functionality before connecting airbrush to compressor
+The tutor will show you these steps in detail:
-*connect airbrush to compressor
+*airbrush and needle functionality (before connecting airbrush to compressor!)
+*how to connect an airbrush to the compressor
 *change compressor pressure settings
-* add paint / change paint / demonstrate how "thin" or "watery" the paint needs to be
+*add paint/change paint
+*how "thin" or "watery" the paint needs to be
+*turn on the fume hood
 *spray examples with varying needle positions (fine line / area fill etc)
-*disconnect airbrush from compressor
+*disconnect the airbrush from the compressor
-*empty compressor / use valve
 *disassemble airbrush
 *clean airbrush
-*reassemble airbrush
+*reassemble & store airbrush
+== Suggested Reading ==
+You can find all airbrushing related pages in '''[[:Category:Airbrushing]]'''.
+Remember: before using '''any''' shared equipment, you MUST read its wiki page!
 [[Category:Introductions]]