Handheld Circular Saw Introduction: Difference between revisions
From CoMakingSpace Wiki
(updated some things to the new Festool saw) |
(linked Festool manual; slight formatting) |
||
| Line 1: | Line 1: | ||
This is the content required for an introduction to our [[Circular | This is the content required for an introduction to our [[Circular Saws|circular saws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | ||
Let's begin! First off, make sure you have read the machine's [https://www.manualslib.com/manual/1230277/Einhell-E-Hks.html#manual manual] | Let's begin! First off, make sure you have read the machine's manual: | ||
* [https://www.manualslib.com/manual/1230277/Einhell-E-Hks.html#manual Herkules BHK 1600LE "Laser Beam"] | |||
* [https://www.manualslib.com/manual/1311650/Festool-Ts-75-Ebq.html Festool TS 75 EBQ] (plunge saw) | |||
== Safety == | == Safety == | ||
| Line 18: | Line 20: | ||
* '''[Festool TS 75]''' When doing a plunge cut make sure the rail/workpiece can't move sideways. This could cause the blade to bind and kickback. | * '''[Festool TS 75]''' When doing a plunge cut make sure the rail/workpiece can't move sideways. This could cause the blade to bind and kickback. | ||
** Attach the endstop to the rail to reduce the chance of kickback | ** Attach the endstop to the rail to reduce the chance of kickback | ||
* '''[Festool TS 75]''' Use an appropriately sized riving knife (DE: Spaltkeil) when using a different blade | * '''[Festool TS 75]''' Use an appropriately sized riving knife ''(DE: Spaltkeil)'' when using a different blade | ||
== Demonstration == | == Demonstration == | ||
The tutor will show you these steps in detail: | The tutor will show you these steps in detail: | ||
* using the [[Circular Saw Guide|circular saw guide]] | * using the proper [[Circular Saw Guide|circular saw guide]] | ||
'''Festool TS 75''' | |||
'''Festool TS 75:''' | |||
* change cutting angle | * change cutting angle | ||
* change and lock cutting depth | * change and lock cutting depth | ||
Revision as of 17:31, 11 December 2018
This is the content required for an introduction to our circular saws - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
Let's begin! First off, make sure you have read the machine's manual:
- Herkules BHK 1600LE "Laser Beam"
- Festool TS 75 EBQ (plunge saw)
Safety
Dangers
- sawdust and small splinters can fly towards the operator and others
- sharp and rotating exposed blade - will keep spinning for a bit after turning the power off!
Precautions
- hook up a shop vac, but be aware the dust extraction from our "Herkules" saw is very incomplete
- wear goggles and ear defenders!
- dust mask: depending on the material you're cutting
- get a helper who can hold your cutoff (depending on the size it) so it doesn't fall down
- make sure the cutting path is free of obstacles (except your workpiece of course)
- let the saw start before touching the workpiece
- keep the saw secure after your cut until is has come to a complete stop
- [Festool TS 75] When doing a plunge cut make sure the rail/workpiece can't move sideways. This could cause the blade to bind and kickback.
- Attach the endstop to the rail to reduce the chance of kickback
- [Festool TS 75] Use an appropriately sized riving knife (DE: Spaltkeil) when using a different blade
Demonstration
The tutor will show you these steps in detail:
- using the proper circular saw guide
Festool TS 75:
- change cutting angle
- change and lock cutting depth
