Search results

Page title matches

• Photo Engraving
  #REDIRECT[[Laser Engraving Photos]]
  35 bytes (4 words) - 09:38, 11 June 2018
• Laser Engraving Photos
  [[:Category:Engraving|Engraving]] photos on various materials can be an awesome alternative to just printin ...ark marble or granite (becomes brighter, so '''invert''' your photo before engraving)
  5 KB (788 words) - 16:24, 18 August 2020
• Linoprint with Laser Engraving Workshop
  # Engraving the motive on linol using a laser cutter ...ge with the default Adobe RGB color space, these images play nice with the engraving software.
  6 KB (1,047 words) - 21:52, 13 March 2022

Page text matches

• Photo Engraving
  #REDIRECT[[Laser Engraving Photos]]
  35 bytes (4 words) - 09:38, 11 June 2018
• Wooden Photos
  #redirect[[Laser Engraving Photos]]
  35 bytes (4 words) - 09:17, 8 June 2019
• Holzfotos
  #redirect[[Laser Engraving Photos]]
  35 bytes (4 words) - 09:17, 8 June 2019
• Laser Engraving Photos
  [[:Category:Engraving|Engraving]] photos on various materials can be an awesome alternative to just printin ...ark marble or granite (becomes brighter, so '''invert''' your photo before engraving)
  5 KB (788 words) - 16:24, 18 August 2020
• VisiCut
  ...ving. Cutting and marking are vector ("line") based while engraving and 3D engraving will work with both vector and raster (pixel grid) files. Also called "vector engraving" - faster than cutting, which results in thin lines on your workpiece but i
  5 KB (720 words) - 22:26, 7 February 2019
• Linoprint with Laser Engraving Workshop
  # Engraving the motive on linol using a laser cutter ...ge with the default Adobe RGB color space, these images play nice with the engraving software.
  6 KB (1,047 words) - 21:52, 13 March 2022
• Laser Cutter
  ...ng the entire duration of a cutting job and being in close vicinity during engraving jobs'''. * stay in close vicinity for the entire job when engraving
  6 KB (872 words) - 22:30, 24 October 2022
• Laserscript LS6090
  ...f cuttable & engravable materials]];<br>[[Laser Cutter#Possible Materials (Engraving Only)|list of only engravable materials]]) * worktable size: 60x90 cm (length x width), engraving a bit smaller
  3 KB (536 words) - 01:36, 5 November 2022
• Laser Cutter Material Settings
  ...ted, 100 % power in a cutting profile is not the same as 100 % power in an engraving profile... <!-- because of different frequencies? --> ...Materials|Forbidden]]''' and '''[[Laser_Cutter#Possible_Materials_(Cutting/Engraving)|Possible Materials]]'''.
  11 KB (1,488 words) - 02:44, 29 February 2024
• Laser Cutter Introduction
  ...r (please reference the list of [[Laser_Cutter#Possible Materials (Cutting/Engraving)|possible materials]] *** set cutting/engraving settings per path
  5 KB (865 words) - 00:20, 2 March 2024
• LaserCut 5.3
  ...aterial by following the defined vectors. You can also use this for vector engraving ("marking") by lowering the power. ...ng_Your_Job|simulate the job]] to avoid bad surprises!). Also see "[[Laser Engraving Photos]]" for advice on pre-processing these.
  12 KB (2,014 words) - 21:08, 9 July 2022
• Wish List
  * rotary attachment for engraving glasses, bottles etc.
  5 KB (621 words) - 19:41, 22 April 2024
• Plenum/Meeting minutes/2022-08-10
  **laser cutting/engraving ([[Sebastian]])
  5 KB (702 words) - 00:31, 11 August 2022
• You can make it
  ** ursprüngliche Planung von [[Keno]] siehe [[Linoprint with Laser Engraving Workshop]] - darf natürlich angepasst werden!
  6 KB (767 words) - 16:38, 23 August 2021
• Plenum/Meeting minutes/2022-09-07
  **laser cutting/engraving ([[Sebastian]])
  6 KB (987 words) - 15:32, 19 September 2022
• Plenum/Meeting minutes/2019-04-10
  *** diode-powered (5 W) - not much cutting ability but nice for engraving
  10 KB (1,663 words) - 13:49, 5 August 2022