User:MobiTobi: Difference between revisions
From CoMakingSpace Wiki
| (3 intermediate revisions by the same user not shown) | |||
| Line 27: | Line 27: | ||
|- | |- | ||
!Plywood 3mm Bubinga (ROBOTIME) | !Plywood 3mm Bubinga (ROBOTIME) | ||
| | |2024-10 | ||
|3 mm | |3 mm | ||
|cut | |cut | ||
| | |26 | ||
|100 | |100 | ||
| | | | ||
| | | | ||
| | |surface | ||
|kerf 0.1 mm | |kerf 0.1 mm | ||
|- | |- | ||
!Plywood 3mm yellow Lime (ROBOTIME) | !Plywood 3mm yellow Lime (ROBOTIME) | ||
| | |2024-10 | ||
|3 mm | |3 mm | ||
|cut | |cut | ||
| | |26 | ||
|100 | |100 | ||
| | | | ||
| | | | ||
| | |surface | ||
| | | | ||
|- | |- | ||
!Plywood 3mm yellow Lime (ROBOTIME) | !Plywood 3mm yellow Lime (ROBOTIME) | ||
| | |2024-10 | ||
|3 mm | |3 mm | ||
|bleech | |bleech | ||
| Line 56: | Line 56: | ||
| | | | ||
| | | | ||
| | |surface | ||
|do NOT use masking tape | |do NOT use masking tape | ||
|- | |- | ||
!Plywood 3mm yellow Lime (ROBOTIME) | !Plywood 3mm yellow Lime (ROBOTIME) | ||
| | |2024-10 | ||
|3 mm | |3 mm | ||
|engraving | |engraving | ||
| Line 67: | Line 67: | ||
| | | | ||
| | | | ||
| | |surface | ||
|DO use masking tape; <br> 2 passes | |DO use masking tape; <br> 2 passes | ||
|- | |- | ||
!acrylic | !PMMA (acrylic glass) extruded | ||
|2024-11 | |||
|3 mm | |||
|cut | |||
|35 | |||
|100 | |||
| | | | ||
|1 | | | ||
|surface | |||
|kerf:0.1 mm | |||
|- | |||
!PMMA (acrylic glass) extruded | |||
|2024-11 | |||
|3 mm | |||
|cut | |cut | ||
| | |45 | ||
|100 | |100 | ||
| | | | ||
| | | | ||
| | |surface | ||
| | |kerf: 0.06 mm | ||
|- | |- | ||
!acrylic | !PMMA (acrylic glass) extruded | ||
| | |2024-11 | ||
|6 mm | |6 mm | ||
|cut | |cut | ||
| | |6 | ||
|100 | |100 | ||
| | | | ||
| | | | ||
| | |surface | ||
| | |visible difference between top and bottom edge; <br> at speed 4 and 8 cutting edges looked less clean | ||
|- | |- | ||
|} | |} | ||
Latest revision as of 11:41, 14 November 2024
Welcome to my page :^)
I am a new member of the comakingspace and new to most tools in the shop.
My current projects are learning to use Autodesk Fusion and the laser cutter.
When I have my materials and introduction to the machine, I already have a bunch of laser cutter projects on my todo list. I want to start small with a bunch of board game knick-knacks, drawer organisers, desk doodads and stationery accessories. Down the line I want to learn about 3D printing and create some basic ATLAS compatible drawer housings.
Always keen to collaborate in block printing projects :D
Materials
| Material | Date
(YYYY-MM) |
Thickness | Operation | Speed (mm/s) | Power (%) | Corner power | Scan gap ("resolution") | Focus | Comments |
|---|---|---|---|---|---|---|---|---|---|
| Plywood 3mm Bubinga (ROBOTIME) | 2024-10 | 3 mm | cut | 26 | 100 | surface | kerf 0.1 mm | ||
| Plywood 3mm yellow Lime (ROBOTIME) | 2024-10 | 3 mm | cut | 26 | 100 | surface | |||
| Plywood 3mm yellow Lime (ROBOTIME) | 2024-10 | 3 mm | bleech | 500 | 20 | surface | do NOT use masking tape | ||
| Plywood 3mm yellow Lime (ROBOTIME) | 2024-10 | 3 mm | engraving | 200 | 40 | surface | DO use masking tape; 2 passes | ||
| PMMA (acrylic glass) extruded | 2024-11 | 3 mm | cut | 35 | 100 | surface | kerf:0.1 mm | ||
| PMMA (acrylic glass) extruded | 2024-11 | 3 mm | cut | 45 | 100 | surface | kerf: 0.06 mm | ||
| PMMA (acrylic glass) extruded | 2024-11 | 6 mm | cut | 6 | 100 | surface | visible difference between top and bottom edge; at speed 4 and 8 cutting edges looked less clean |
