Wood Lathes: Difference between revisions

From CoMakingSpace Wiki

m (German name)
(new lathe commissioning)
Line 96: Line 96:
* it would be nice to fix the control box more properly - this should be coordinated with Micha Ba. who is the machine's owner!
* it would be nice to fix the control box more properly - this should be coordinated with Micha Ba. who is the machine's owner!
* get/make a faceplate and a drive center for more workholding flexibility
* get/make a faceplate and a drive center for more workholding flexibility
== Tyme Avon ==
{{Commissioning
|IssueNumber=
|Naming=
|NamingComment=Tyme Avon
|Picture=
|PictureComment=
|Manual=
|ManualComment=print version for sale (expensive) [http://www.lathes.co.uk/tyme/ here]
|Documentation=
|DocumentationComment=explain (& photograph?) all major accessories and setup options; possible starting point besides manual: http://www.lathes.co.uk/tyme/
|QR=
|QRComment=
|Introduction=
|IntroductionComment=[[Woodturning Introduction]] may need slight changes - TBD
|Security=
|SecurityComment=needs EU plug - and also a longer cord while we're at it?; belt runs into the side of its pulleys -> shim the motor to move it out approx. 1 mm?
|Test=
|TestComment=
|OwnerValue=
|OwnerValueComment=donated by Joe; value not yet known
|Availability=
|AvailabilityComment=
}}


== Further Reading ==
== Further Reading ==

Revision as of 15:27, 24 April 2022

MachineInfoBox

Wood Lathes

Synonyms: woodturning lathes; DE: Drechselbänke,
Drechselmaschinen
Type: [[lathe]]
Material: woodturning blanks
Used with: face shield, woodturning tools
Location: wood workshop
Access Requirements: Woodturning IntroductionThe part "]]" of the query was not understood.</br>Results might not be as expected.
Tutors: LukasThe part "]]" of the query was not understood.</br>Results might not be as expected.
Similar (More or Less): metal lathe

[[MachineType::lathe| ]]


We have wood lathes in the wood workshop that can be used as an entry to woodturning - once a community of turning enthusiasts develops and the machines become too weak for more ambitious projects, we can think about replacing them with a professional model.


Güde 1000

MachineInfoBox

Güde 1000

Güde 1000.JPG
Type: [[lathe]]
Material: woodturning blanks
Used with: face shield, woodturning tools
Location: wood workshop
Access Requirements: Woodturning IntroductionThe part "]]" of the query was not understood.</br>Results might not be as expected.
Status: [[Has InfoBox Status::functional
(needs some more documentation)]]
Manual: Guede.com
Tutors: LukasThe part "]]" of the query was not understood.</br>Results might not be as expected.

[[Has caption::lathe| ]] [[MachineType::lathe| ]]


The "Güde" wood lathe is very simple, but okay for learning how to turn wood.

Caution - Overheats Old Fuses

This lathe may trip an old-fashioned fuse (circuit breaker, Sicherung) when turned off an on repeatedly as every start of the motor draws a lot of power. To prevent this issue, plug the lathe into the "modern" black/white outlet box below the main power Verteiler to the right of the lathe! Please ask a tutor or manager if you're not sure about any of this.

Specs

  • max. workpiece diameter: 320 mm
  • max. workpiece length: 1000 mm
  • spindle speeds: 850 - 1250 - 1750 - 2510 rpm
  • motor: 370 W
  • spindle thread: M18
  • workholding options: drive center (Vielzack-Stirnmitnehmer/"Dornenkrone"), four-jaw chuck, faceplate (wrong thread)

Speed Selection

The lathe can run at various speeds depending on which pulleys are connected by the belt (picture on the housing). Do not put excessive tension on the belt - you'll be very happy about the belt slipping in case you've made a mistake and the tool digs into the workpiece!

Upgrades/Improvements

We have tweaked this machine to improve usability (also see issue #7) :

In addition, these accessories might be interesting in the future:


Holzmann D 460F

MachineInfoBox

Holzmann D 460F

Holzmann D460F.jpg
Type: [[lathe]]
Material: woodturning blanks
Used with: face shield, woodturning tools
Location: wood workshop
Access Requirements: Woodturning IntroductionThe part "]]" of the query was not understood.</br>Results might not be as expected.
Status: operational
Manual: maschinenhandel-gronau.de (DE)
Tutors: LukasThe part "]]" of the query was not understood.</br>Results might not be as expected.

[[MachineType::lathe| ]]



SAFETY NOTE: Make sure you lock the box with the on/off switch in place before use! DO NOT start the lathe when it can swivel, you may not be able to safely turn it off then and the belt/pulleys are exposed!

Specs

this lathe can be used with a drill chuck!
  • max. workpiece diameter: 254 mm
  • max. workpiece length: 450 mm
  • spindle speeds: 650-3800 rpm (variable)
  • motor: 370 W
  • spindle thread: M33
  • workholding options:
    • headstock: four-jaw chuck
    • tailstock: morse taper - accessories: rotating center, drill chuck

Speed Selection

The D 460F has an electronic speed selection which is regulated by a potentiometer (without scale!) above the on/off switch.

Upgrades/Improvements

Ideas:

  • it would be nice to fix the control box more properly - this should be coordinated with Micha Ba. who is the machine's owner!
  • get/make a faceplate and a drive center for more workholding flexibility

Tyme Avon

This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task comment Status
Name the tool: Tyme Avon pending
Take a picture - pending
Find the manual as PDF print version for sale (expensive) here pending
Documentation explain (& photograph?) all major accessories and setup options; possible starting point besides manual: http://www.lathes.co.uk/tyme/ pending
Print QR-Code use the wikicrawler pending
Introduction Woodturning Introduction may need slight changes - TBD pending
Security Check needs EU plug - and also a longer cord while we're at it?; belt runs into the side of its pulleys -> shim the motor to move it out approx. 1 mm? pending
Test to be done or witnessed by a manager pending
tool's name, owner and approx. value donated by Joe; value not yet known pending
Last step: make it available physically and in the wiki - then delete this template pending



Further Reading