Scroll Saw

From CoMakingSpace Wiki

Revision as of 11:32, 17 February 2019 by Lukas (talk | contribs) (I think it's good to keep the original "overview" photo as well, so people can place the GIF)

ToolInfoBox

Proxxon DSH

ScrollSaw.gif
Synonyms: DE: Dekupiersäge,
Feinschnittsäge
Type: power tool/saw
Material: wood, plastics, non-ferrous metals
Location: wood workshop
Access Requirements: after a personal introduction
Tutors: Lukas, Mitja, Martin
Manual: amazon.com PDF
Similar (More or Less): fretsaw, bandsaw, laser cutter
cutting parts for Project:Schneckchen

A scroll saw can be described as a powered fretsaw: two arms at the top and bottom hold a thin saw blade and vibrate quickly. The workpiece is pushed through the otherwise stationary saw blade to cut. It is a very versatile tool and can be used to cut wood, plastics or many metals to obtain intricate shapes. For larger pieces with wider curves you may want to use a jigsaw.

Cutting capacity is 50 mm in wood, 30 mm in plastics and 10 mm in non-ferrous metals. [1]

Don't forget to wear personal protection and hook up a shop vac when you use it!

Saw Blades

Saw blades have to be changed frequently due to wear, different materials or simply because you want to cut a hole and have to enter the workpiece.

We use quick-release saw blades with pins on both ends, do not screw these in or they will break! Saw blades without pins have to be secured by screws on both arms of the machine. The teeth of the saw blade always have to point down and a hole will need to be at least 5.3 mm in one direction for the blade to fit through because of these pins.

Changing Saw Blades

  • unplug the machine
  • turn the tensioner (knob in the back) counterclockwise to loosen
  • push the top arm down
  • unhinge the saw blade from the top and bottom arm
  • insert a new saw blade (teeth pointing down, pins carefully hooked in their grooves)
  • turn the tensioner clockwise until the blade makes a high-pitch noise when plucked
  • continue working


Types of Saw Blades

MaterialInfoBox

Scroll Saw Blades

Scroll saw blades.JPG
Synonyms: DE: Dekupiersägeblätter
On Site? soon
Suggested Donation: 50 ct
Suggested Tools: scroll saw

Your material and to some extent also the design you want to cut dictate which saw blades can be used.

Our scroll saw works with 127 mm saw blades which come in different versions:

  • coarse (10 teeth per inch/25 mm)
    • appropriate for soft and hard wood and thick materials
    • Proxxon NO 28 741
  • normal (18 teeth per inch/25 mm)
    • appropriate for soft and hard wood, plastic and thin materials
    • Proxxon NO 28 743
  • fine (25 teeth per inch/25 mm)
    • appropriate for plastic, glass-fibre reinforced plastic, non-ferrous metals, acrylic glass and wood
      • Caution with acrylic glass: the material tends to weld the cut closed due to the high temperature being generated and thus prevents backward motion - make sure you will be able to cut in one go or you might get stuck! Consider drilling relieve holes along the cutting path to allow for easy turning and exit points. Also cutting straight lines into acrylic glass tends to result in wave-like patterns as the blade is flexible and therefore oscillates around the cutting path.
    • Proxxon NO 28 745
  • round (16 teeth per cm)
    • not in stock yet
    • allow for free turning of the workpiece and very tight corners
    • appropriate for plastic and soft or hard wood
    • Proxxon NO 28 747

Where to Cut?

Even for a "free-hand" design you make your work easier if you sketch the cut on your workpiece, e.g. with a pencil on wood or a scriber on metal and plasic. For printed plans, the easiest option is to glue them onto the workpiece - with glue sticks (they're water soluble) or onto a layer of masking tape which should later peel off without a trace.

Inspiration