Handheld Routers

From CoMakingSpace Wiki

Revision as of 20:27, 11 September 2019 by Pakue (talk | contribs) (Removed Bosch router as it is gone for good)

MachineInfoBox

Routers

Ferm FBF-1050E.JPG
Synonyms: plunge routers, handheld routers;
DE: Oberfräsen, Handoberfräsmaschinen
Type: power tool
Material: wood
Used with: router bits
Access Requirements: Handheld Router Introduction
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis
Similar (More or Less): CNC router, router plane; milling table, CNC mill


A router is basically a powerful motor spinning a sharp metal bit at high speeds. Read the manual before using and be aware of the difference between the regular "push" and the more dangerous "climb" cut!

Safety

Routers are very dangerous tools, make sure you have received the handheld router introduction in person and take time to think about what you are going to do!

Router Bits

(main article: Router Bits)

Router bits can get quite expensive, but good quality ones can be sharpened when they become dull.

Typical collet (Spannzangen) sizes are 6 and 8 mm.
A simple shared set of 8 mm router bits is available in the wood workshop. As always, report when broken and replace them accordingly.


Copying Rings

Copying rings can be used for template work and are more versatile (although a bit more complicated) than flush trim bits with a ball bearing that takes care of the copying. When working with a copying ring, the template has to be offset from the target shape by a few millimeters: offset = (outer coyping ring diameter - bit diameter)/2 [1]

Future Plans

Interesting Links


Makita DRT50

MachineInfoBox

Makita DRT50

Makita-DRT50.jpeg
Location: chop saw station
Access Requirements: Handheld Router Introduction
Manual: Makita
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis


The router has its own box (Makpack) with all its accessories (DRT50RTJX2). It is battery powered with 18V Makita lithium batteries that are shared with our other Makita tools like the cordless drill. The set consists of:

  • flat surface attachment w/o grips
  • flat surface attachment with grips
  • edge cut attachment
  • 2x vacuum dust attachment
  • long grip (can replace one of the stud grips on the flat surface attachment)
  • roller attachment for routing edges with bits lacking a bearing


KingCraft KBF-1050E

MachineInfoBox

KingCraft KBF-1050E

Router Table.JPG
Location: Martin's locker
Access Requirements: Handheld Router Introduction
Status: [[Has InfoBox Status::broken]]
Manual: ferm.com
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis


broken tool - this section may be removed soon, ignore it for now! You can use the Ferm router in the router table if you need to

Martin brought a router which is attached to the router table.

We currently have 6 and 8 mm collets for it (an extra 8 mm one is in the storage room along with replacement carbon brushes).

The depth setting screw is very useful for fine adjustments, but when it is loose and the router is mounted upside down it can fall out because of the vibrations. Therefore, this screw should be used to hold the router in position under the router table instead of the clamping lever on the back. Unfortunately, one of the falls seems to have broken the handle off the screw, both parts are currently in the box with broken equipment on the ladder shelf.

Repairs & Upgrades

Watch out! This tool has been repaired for now, but may suffer another defect in the near future. If anything looks, feels or sounds wrong to you, do not use it and immediately talk to a tutor or manager!

  • 2018-11-25 (after approx. 5 uses of the router table; ask Lukas for more details)
    • cast metal "collar" discovered to be broken in several places, spindle locking button put back in position with a zip tie (epoxied to the collar so it can't slip off)
    • cut a longer thread into the depth setting screw so it can be tightened in any router position
  • 2019-3-27
    • previous hack broken a few days before as reported in issue #105
    • locking collar removed, 14 mm wrench added to the router table for locking


Ferm FBF-1050E

MachineInfoBox

Ferm FBF-1050E

Ferm FBF-1050E.JPG
Location: wood workshop (chop saw station)
Access Requirements: Handheld Router Introduction
Manual: pdf
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis


This router comes with 6 and 8 mm collets (Spannzangen). A few other accessories, including a parallel fence, can be found in its box.

This router can be mounted in the router table!

A set of router bits is available with the router. As always, report when broken and replace them accordingly.

Past repairs:


Private Tools

Einhell TE-RO 1255 E

MachineInfoBox

Einhell TE-RO 1255 E

Einhell router.JPG
Location: Mitja's CoMaking bench
Access Requirements: Handheld Router Introduction
Manual: pdf
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis


Mitja owns an Einhell router that you may be able to use for your projects if you ask him nicely.