Reciprocating Saw Introduction: Difference between revisions

Revision as of 22:26, 25 March 2020

This page is INCOMPLETE and still missing some important information before it can be used as a resource. Please use the "Discussion" feature above or talk to one of the tutors if you would like to help improve it. Thanks!

This is the content required for an introduction to our reciprocating saw and jigsaws - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

Let's begin! First off, make sure you have read the corresponding tool's manual:

Safety

Personal protection:

perhaps also wear a dust mask (depending on the material you're cutting)

Dangers	Precautions
sharp oscillating blade - possible kickback	never turn on the saw when the blade is already touching something (e.g. the workpiece) always let the baseplate touch the workpiece before starting to cut blind cut: leave the sawblade in the cut until it has stopped through cut: make sure the blade has stopped moving before putting the saw back on the table make sure the blade path is free and you won't cut into the table or similar make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback) before cutting into the workpiece, make sure there are no obstacles such as nails in it secure the workpiece with clamps so nothing shifts and nothing large falls down once the cut is made
generates dust and small chips	wear goggles hook up the shop vac (and deactivate the "dust blow" function of the saw, if available)
generates noise	wear ear defenders
no prevention of turning on after loss & restoration of power (keine Anlaufsicherung)	make sure the locking lever isn't "on" before plugging the saw in (the trigger should move freely)

Demonstration

During the introduction, the tutor will show you the following:

inserting/removing saw blades
choosing and changing the pendulum or orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)

Besides these safety notes, you should know which type of blade is suitable for the material you want to cut!

@@ Line 1: / Line 1: @@
-This is the content required for an introduction to our [[Reciprocating Saw| reciprocating saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+{{incomplete}}
-Let's begin! First off, make sure you have read the tool's manual (Bosch PFZ 700 PE: [https://www.manualslib.com/manual/1125358/Bosch-Pfz-700-Pe.html here]).
+This is the content required for an introduction to our [[Reciprocating Saw| reciprocating saw]] and [[jigsaws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+Let's begin! First off, make sure you have read the corresponding tool's manual:
+* [https://www.manualslib.com/manual/1125358/Bosch-Pfz-700-Pe.html Bosch PFZ 700 PE]
+* [http://www.lidl-service.com/static/134937369/114249_DE.pdf Parkside PSTD 800 A1]
+* [https://www.manualslib.com/manual/1115989/Bosch-Pst-650-Pe.html Bosch PST 750 PE]
 == Safety ==
-=== Dangers ===
+[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]]
-* sharp oscillating blade - possible kickback
-* generates dust and small chips
-* generates noise
-=== Precautions ===
+''perhaps also wear a [[Dust Masks|dust mask]] (depending on the material you're cutting)''
+{| class="wikitable"
+|-
+! Dangers !! Precautions
+|-
+| sharp oscillating blade - possible kickback ||
+* never turn on the saw when the blade is already touching something (e.g. the workpiece)
+* always let the baseplate touch the workpiece before starting to cut
+* blind cut: leave the sawblade in the cut until it has stopped
+* through cut: make sure the blade has stopped moving before putting the saw back on the table
 * make sure the blade path is free and you won't cut into the table or similar
-* make sure the blade is long enough so that it can reach through the material when fully retracted. (too short a blade relative to the material being cut will cause dangerous kickback)
+* make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback)
 * before cutting into the workpiece, make sure there are no obstacles such as nails in it
 * secure the workpiece with [[clamps]] so nothing shifts and nothing large falls down once the cut is made
+|-
+| generates dust and small chips ||
 * wear [[goggles]]
-** perhaps also wear a [[Dust Masks|dust mask]] (depending on the material you're cutting)
+* hook up the [[Shop Vac|shop vac]] (and deactivate the "dust blow" function of the saw, if available)
-* wear [[Ear Defenders|ear defenders]]
+|-
-* make sure the locking lever isn't "on" before plugging the saw in (the trigger should move freely)
+| generates noise || wear [[Ear Defenders|ear defenders]]
-* make sure the blade is not moving before putting the saw back on the table
+|-
-* in order to avoid kickback: never turn on the saw when the blade is touching something (e.g. the workpiece)
+| [[File:Danger_-_sudden_start.svg|left|50px]] no prevention of turning on after loss & restoration of power (''keine Anlaufsicherung'') || make sure the locking lever isn't "on" before plugging the saw in (the trigger should move freely)
-* always let the baseplate touch the workpiece before starting to cut
+|}
-* leave the sawblade in the cut until it has stopped
 == Demonstration ==
 During the introduction, the tutor will show you the following:
 * inserting/removing saw blades
-* choosing and changing the orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)
+* choosing and changing the pendulum or orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)
 Besides these safety notes, you should know which type of blade is suitable for the material you want to cut!