LaserCut 5.3

From CoMakingSpace Wiki

The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
SoftwareInfoBox

LaserCut 5.3 or Lasercut 5.3

LaserCut53 entry.jpg
Type: laser cutter driver/CAM
Platform: Windows (XP, 7, 8, 10 [1])
License: proprietary
Source:
Installed on: laser PC
Input Formats: PLT, AI, DXF, DST, BMP, NC, JPG, GIF, PNG, TIF, TGA, PCX
Output Formats: MOL
Users: Martin


Lasercut 5.3 is required to prepare a design file for our laser cutter. Its drawing functions are apparently quite terrible, so pretty much all users in forums etc. recommend to only use it for the very last steps!

If you are familiar with "our" previous laser cutter (the loaned Epilog Zing), this software will pretty much take over what you used to do with Visicut.

LaserCut 5.3 is installed on a dedicated PC, which is located next to the laser cutter itself.


Installation

We got a copy of LaserCut 5.3 from HPC Laser. You can get it from the orange USB drive located next to the laser cutter. However, the version we got does only work with the "soft dog" USB dongle, which will be attached permanently to the dedicated PC.

In order to prepare files on your own computer, you can install the software from another source. Most sources include an executable called "Lasercut53_Demo.exe" which can be used without the dongle but cannot operate the machine itself. The demo version also does not want you to save or open project files, but there are workarounds:

  • saving is reportedly offered when closing the program
  • opening of a finished project is best done with our full version at the Space, but also possible after some "terrible" exporting/re-importing [2]

In case you plan to do these, please make sure that you replace your syscfg.ini with the one shipped with our laser (can be found on the mentioned USB drive).

Installation notes:

  • The software only natively works on Windows. Try Wine or other methods at your own risk, but be aware it's 32-bit software
  • The software must be installed in C:\LaserCut53 in order to work properly. There is a parameter in syscfg.ini which indicates the installation path. Changing it might get it to work from other locations as well but is untested. Try at your own risk.

Setup

Setting the Worktable Size

The first thing to do after installation is to check for the correct worktable size. Our laser has a size of 90x60 cm. Please ensure your worktable is set up correctly.

If it is not, you can change it by navigating to File --> Machine Options (or pressing Ctrl+J).
In the new window, please navigate to "Worktable" and apply the following settings:

  • X Axis [Range] 900.0
  • Y Axis [Range] 600.0

When clicking "Save", it will most likely ask you for a password. Just hit "OK".

Basic Usage

Zoom to All Objects

LaserCut53 ZoomToAllObjects.jpg

Sometimes you need to ensure that all your objects are visible on the screen. To do so, please use Zoom to all objects

LaserCut53 ZoomToAllObjects Result.jpg

Note: You can use this tool in order to ensure all your objects are on the worktable. Objects outside the worktable will result in a soft stop of the laser.

Zoom to Table

LaserCut53 ZoomToTable.jpg

This tool is particulary helpful in case you zoomed in or out of your worktable and want to see the entire worktable centralized on your screen:

LaserCut53 ZoomToTable Result.jpg

Preparing a Job

Import Your File

The first thing you need to do is to import your drawing. You can do so by navigating to File --> Import or by pressing Crtl+I. The following file formats are supported:

  • PLT
  • DXF
    • Fusion 360: export the file. Do not just "save as".
    • Inkscape: reportedly, the checkboxes "Use ROBO-Master type of spline output" and "Use LWPOLYLINE type of line output" need to be off when saving as DXF for LaserCut 5.3 [3]
  • AI (Adobe Illustrator)
  • JPG
  • GIF
  • PNG
  • BMP
  • TIF
  • DST
  • NC
  • TGA
  • PCX

Preparing the Cut Paths

Once your file is imported, you will see the preview on the screen. The following tools might be handy when preparing your cut paths:

Unite Lines

before uniting the lines
after uniting the lines

In case you just start your job without any further tuning, you might recognize that the laser follows an odd order of steps to cut your paths.

In order to streamline this, please select the paths of your model and navigate to Tools --> Unite Lines.

LaserCut53 UniteLines Options.jpg

Note: The default value of 0.100 as the unite tolerance is usually a pretty good value to recognize lines belonging together.

Output Order

"layers" can be prioritized by moving them up in this list

You often want to engrave before cutting as the cut parts can fall out of focus when they are separated from the rest of the material.

easy way: select a "layer" in the list on the right and move it around with the Up or Down buttons (top is done first, bottom last)

You can also control the order of the cuts by navigating to Tools --> Output Order: In the new window, you will get a list of output layers, which you can put into the desired order by selecting them on the left and moving them to the right side of the window.
If you are not sure which number corresponds to which cutting path, please note that you can select lines while having the output order window open.

Setting the Entry Point

On each path you can select the entry point the laser will use by using the "Define cut route" tool. You can find this in the menu as Laser --> Define cut route or in the menu bar:

LaserCut53 DefineCutRoute.jpg

Hint: If you press space when using this tool, a new window will open allowing you to edit some expert settings:

LaserCut53 DefineCutRoute Lead InOut Options.jpg

Copy

Especially when mass processing something, you might want to copy your drawing multiple times. LaserCut offers a few different options to do so:

  1. Mark the paths, use CRTL-C and CTRL-V, then move the new paths
  2. Mark the paths, navigate to Draw --> Copies
    This will create actual copies of your object in an array which you can define. After the copies have been created, they are independent of each other and can be modified and moved seperately.
  3. Mark the paths, navigate to Laser --> Array output options
    This will allow you to laser your paths multiple times. Please note that the copies are not independent of each other and can only be moved together. Also, the same settings apply for all of them.

Selecting the Laser Mode

Mode Explanation
Cut Cuts your material by following the defined vectors. You can also use this for vector engraving ("marking") by lowering the power.
Engrave Engraves the shapes of your drawing into your material (similar to a printer).

With bitmap pictures, this will engrave dark parts of your picture into your workpiece (simulate the job to avoid bad surprises!). Also see "Laser Engraving Photos" for advice on pre-processing these.

Caution: with vector drawings, this will engrave the entire area of your drawing into your workpiece.

Grade Engrave Grade engraving will tell the laser to bevel the corners of your engraving. This should increase readability of letters for example.
Hole This setting is similar to cutting. It will follow the defined lines, but will only make little dots (holes) into your material.
Pen Cut This setting seems to crash LaserCut 5.3 and is not documented in the manual.

Setting Power and Speed

You can set the power and speed for each layer separately in the Control Panel:

LaserCut5.3 PowerOptions.jpg

Here you can select the desired mode by using the correspondent drop down menu.

Double-clicking on a layer will open the speed settings for the specific layer. Please note that the options for cutting and engraving differ from each other:

Options for cutting

Options for engraving

Please pay special attention to the "Corner Power". Usually you want to set this slightly lower than your regular power (too high and you might get "dogbone" curves instead of nice sharp corners).

Simulating Your Job

To see how the laser will move, press the Simulate Button.png on the far right of the toolbar or navigate to Laser --> Simulate:
Simulate Button 2.png

This is strongly recommended to avoid surprises that ruin your material!

Estimating Work Time

You may press the Estimate Work Time Button.png button on the far right of the toolbar to estimate runtime (i.e. approximate cost) before starting the job.

However, please be aware that this estimate is usually a bit too low (the job will take longer in reality) and pay for the actual time needed in the end!

Controlling the Laser

In the following, "control panel" refers to this section on the right side of the screen:
LaserCut Control Panel.jpg

Homing

In order to home the laser, please press Datum. [1]

Homing the laser will cause it to move into the upper right corner. Please always home the laser before you use it (it should happen automatically during start-up).

NOTE: You can also home the laser by pressing Datum on the control panel of the machine itself.

Moving the Laser

You will need to move the laser to its correct starting position, which you decided on when you prepared your job.

In order to do so, you can use the X-/X+ and Y-/Y+ buttons in LaserCut's control panel or the corresponding arrow keys on the machine.

Please note that you cannot control the Z height from within LaserCut. You will need to set the proper height on the machine itself!

Uploading Your Job

Once you are done with all preperation steps, you need to put your job on the machine. In order to do so, please press the DownLoad button in the control panel. This will open a window called "Stand-alone file manager":

Stand-alone file manager.png

In here, you can select your desired job and press Download file. You can usually just hit Download current to put the latest job onto the machine.

If you want to store this exact setup and machine data for further copies, you can export the data by pressing Export file. This will allow you to save it as a .mol file.

Starting and Stopping the Job

You can start the job in LaserCut or on the machine.

Please note that it is recommended to always control the job from the laser itself!

If you do have a valid reason to start it from LaserCut, please use the Start button on the control panel. You can also pause and stop the job by using the corresponding buttons.

Further Reading

  1. Fun Fact: "Datum" is not a strange translation, but actually the correct term (see Wiktionary)