Jointer-Planer: Difference between revisions

From CoMakingSpace Wiki

(added Waiting List)
(moved waiting list to introduction page)
Line 90: Line 90:
* instead of a thickness planer, you can use [[Bench Planes|bench planes]] or a handheld [[planer]]
* instead of a thickness planer, you can use [[Bench Planes|bench planes]] or a handheld [[planer]]


{{Waiting List}}
 


[[Category:Woodworking]]
[[Category:Woodworking]]

Revision as of 20:38, 16 September 2020

MachineInfoBox

Hammer A3-31

Hammer A3-31.jpg
Synonyms: planer-thicknesser, power jointer, thickness planer;
DE: Abricht- und Dickenhobelmaschine, "Abrichte", "Dickte"
Material: naturally structured wood
(not more engineered than glued laminated timber!)
Location: CNC Area
Access Requirements: Jointer-Planer IntroductionSome use of "" in your query was not closed by a matching "".
Status: [[Has InfoBox Status::in commissioning]]
Manual: felder-gruppe.at (DE), (EN)
Tutors: Lukas
Pakue
Sebastian
LoewensteinSome use of "" in your query was not closed by a matching "".
Similar (More or Less): jointer plane, planer


A jointer is used for straightening the narrow sides of wooden boards which is necessary for panel glue-ups and some kinds of joinery. It basically consists of a flat surface with a slightly protruding cutting drum at the center.

We chose to get a combination jointer/planer to save valuable space: thanks to the second flat surface under this cutting drum, you can also thickness boards with this machine!


This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task comment Status
Name the tool: - done
Take a picture - Done
Find the manual as PDF felder-gruppe.at (DE), (EN) done
Documentation this page, status: in commissioning pending
Print QR-Code use the wikicrawler pending
Introduction Jointer-Planer Introduction Done
Security Check printed manual needs to be kept at the machine (done), push blocks need to be adapted with pins that fall down behind the workpiece (and/or make a new one with a lip) Done
Test to be done or witnessed by a manager Done
tool's name, owner and approx. value provide to Patrick for inventorization Done
Last step: make it available physically and in the wiki - then delete this template pending


Accessories

Dust evacuation

The planer should only be used in tandem with a suitable dust evacuation system. The intended machine for this purpose is the Felder AF 14, that should be in close proximity to the planer. The system should be hooked up through the automated switch box (switched output) mounted on the metal frame, that should also be connected to the planer (trigger output). Once the planer is started the vacuum system will turn on after 3 seconds and turn off once the planer is off for 8 seconds. Make sure to set the switch on the vacuum motor to 'ON' before starting!


Buying rough sawn wood

With our Jointer-Planer, you are able to buy rough sawn wood from wholesalers, your favorite construction market - or even directly from one of the saw mills in the surrounding area. Depending on how rough the wood is, you'll have to plan on removing between 2 and 4mm of material per large face and up to 10mm on the smaller faces of the wood - this is due to the sawing marks on the larger faces and on the often non-squarely cut smaller faces. In construction markets, the rough wood tends to be on the lower end of the amount of material to be removed, while wholesalers or mills tend to be on the upper end of material to be removed. So, you should buy your base wood oversized and rather too large than too small.

While construction markets like Bauhaus, Hornbach or Obi usually have fixed prices depending on cut and size and are rather expensive, wholesalers and saw mills price their wood by volume and are often open for negotiation - you usually directly get 3% off when paying immediately, if you ask. Always ask beforehand, if the volume is calculated *before* drying (which is often the case for domestic woods) or *after* drying (which is often the case for imported wood) - this may change the price by up to 15%.


Buying wholesale or at a saw mill

You should bring a pocket ruler and (optionally) a small hand plane.

If you want the best bargain, you should also check, if the wood has been Air Dried (noted by the abbreviation AD) or Kiln Dried (abbreviated by KD) - the former is usually 10-20% cheaper than the latter. Air dried wood has gotten a lot longer time to dry out, which also reduces the internal stress - air-dried wood tends not to warp and rip as much as kiln-dried wood, but both are completely fine to buy.

When choosing woods, it's accustom for you to choose the exact pieces you want, which usually have to buy whole. You usually are allowed to bring a small plane and can ask to plane a small area to check the grain. Also bring a pocket ruler to determine the sizes, since each piece will have it's own size. Should the wood have a split at the end, this piece has to be cut or will continue to rip apart later one. It's okay to not take that board or negotiate the price down.

Wood ring direction.png (Source)

You should also check the end face and identify the cut - especially if you plan to use the wood outside, where the environment will cause the wood to shrink and expand.

  • if the wood grain lies flat, the board tends to warp uniformly and a lot (fig a)
  • if the wood grain stands (fig b), the board will not warp
  • if the wood grain is diagonally (fig c), the board tends to warp unpredictably, but not as much as in figure a

If you've chosen your boards, an employee of the wholesaler or saw mill will calculate the price, which you usually have to pay now. They usually will shorten the board roughly with a chainsaw (transport cuts) to fit them in your vehicle.


Time and effort / price

Depending on the hardness of your wood, you can take of more or less depth in one pass on the jointer or planer. To give you a rough idea: User:Lars bought 12 pieces à 1000x300x55mm of rough sawn hardwood from a wholesaler. It took 2 hours to get the 12 pieces flat and square on 3 sides and reduced the width of the boards to 49mm and another 20 minutes to get them to their final thickness of 45mm. Add another 15 minutes for cleanup of the machine. This produced 2 sacks of saw dust.

If the wood would have been a softwood from a construction market, the first part would have taken around 1 hour instead of 2 hours. Still, in contrast to hand planing with a bench plane, it's probably a fifth of the time needed otherwise.

Some saw mills might also joint and plane this for you, which is a service you'll obviously have to pay extra for. Still, in comparison to buying pre-planed and joined hardwood, it's a lot cheaper to do it yourself. Remember: Jointing and planing dulls the knifes of the machine a lot and the saw dust has to be recycled - your member fee does not include those costs, so remember to leave a share.


Alternatives