Drill Presses: Difference between revisions

From CoMakingSpace Wiki

m (aka column drill, similar: drill stand)
m (switching to a machine and add location and tutors as SMW parameters)
Line 1: Line 1:
{{ToolInfoBox
{{MachineInfoBox
|tool name=Einhell TB 13/5 ED
|machine name=Einhell TB 13/5 ED
|image=Drill press TB13-5ED.jpg
|image=Drill press TB13-5ED.jpg
|synonyms=bench drill, pillar drill, column drill;<br>DE: Säulenbohrmaschine,<br>"Tischbohrmaschine",<br>"Bohrständer", "Senkbohrer"
|synonyms=bench drill, pillar drill, column drill;<br>DE: Säulenbohrmaschine,<br>"Tischbohrmaschine",<br>"Bohrständer", "Senkbohrer"
|type=power [[Drills|drill]]
|type=power [[Drills|drill]]
|access=after a [[Drill Press Introduction|personal introduction]]
|access=[[Drill Press Introduction]]
|location=[[Drilling Table|drilling table]]
|location=[[Location::Drilling Table|drilling table]]
|material=depending on the [[Drill Bits|drill bit]]:<br>[[wood]], [[plastic]], [[metal]]
|material=depending on the [[Drill Bits|drill bit]]:<br>[[wood]], [[plastic]], [[metal]]
|tutors={{P}}, [[Lukas]]
|tutors=[[Tutor::User:Pakue|Patrick]], [[Tutor::User::Lukas|Lukas]]
|manual='''very''' similar to [http://www.guede.com/sys/dl/55120_55190_55192_55193_55194_55195_55197_55423_55435_ml.pdf "Güde GTB 13/5"]
|manual='''very''' similar to [http://www.guede.com/sys/dl/55120_55190_55192_55193_55194_55195_55197_55423_55435_ml.pdf "Güde GTB 13/5"]
|similar=[[Drill Stand|drill stand]], other [[drills]]
|similar=[[Drill Stand|drill stand]], other [[drills]]

Revision as of 20:31, 13 June 2019

MachineInfoBox

Einhell TB 13/5 ED

Drill press TB13-5ED.jpg
Synonyms: bench drill, pillar drill, column drill;
DE: Säulenbohrmaschine,
"Tischbohrmaschine",
"Bohrständer", "Senkbohrer"
Type: [[power drill]]
Material: depending on the drill bit:
wood, plastic, metal
Location: drilling table
Access Requirements: Drill Introduction
Manual: very similar to "Güde GTB 13/5"
Tutors: Lukas
NitramLegov
Pakue
Lmnl99
Johannes
Luzian
Keno
Jakob
Similar (More or Less): drill stand, other drills

[[Has caption::power drill| ]] [[MachineType::power drill| ]]


To use the machine, you'll need to mount a drill bit that suits your workpiece and securely fasten it with the chuck key.

We got this machine when it was pretty old already so Patrick took it apart, cleaned and painted it. Something in the pulleys still isn't centered which causes slight vibration in the machine. It isn't much of an issue as the shaft is quite rigid and runs true.

The drill bits can sometimes be a little off center as the chuck is not that great - just quickly check before drilling. It often helps to twist the bit back and forth with one hand while closing the chuck with the other.

Safety

  • read the manual!
  • get a personal introduction by one of the tutors!
  • wear personal protection, but never operate the drill press with gloves on!
  • don't drill materials with harmful dust!
  • make sure there is nobody nearby who might be surprised by a piece of shrapnel flying their way!
  • use a machine vise for small workpieces!
  • never use a machine vise on top of a wooden board or two wooden boards at the same time (tower rule)!

Fastening Options

a lever clamp can be used for some workpieces such as this door handle shaft

Jigs

  • V-block for drilling into round or angled things



Shortcomings/Upgrade Potential

the depth stop of the Einhell drill press is made of a flexible material, reducing its precision - while this can often be ignored, it is important to remember for fine work

Until there is money left over for a newer/fancier drill press, we can collect desirable features here:

  • more stable depth stop (see photo)
  • electronic speed control instead of manual change of belts
  • larger "throat size" (distance from the drill bit to the stand)
  • safety: clear chuck guard (probably rather common nowadays)
  • anything else?