Chop Saw

From CoMakingSpace Wiki

Revision as of 18:20, 26 January 2020 by Lukas (talk | contribs) (Undo revision 7972 by Lukas (talk) - miracle cure!)

MachineInfoBox

Herkules KSZ 2100

Herkules KSZ 2100.JPG
Synonyms: sliding compound miter saw;
DE: Kappsäge, Kapp-, Zug- und
Gehrungssäge, Zugkappsäge
Type: [[power tool/saw]]
Material: wood
Used with: circular saw blades, shop vac, inclinometer
Location: chop saw station
Access Requirements: Chop Saw Introduction
Manual: ManualsLib
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis
Sebastian
Jakob
Loewenstein
Similar (More or Less): miter saw, circular saw, table saw,
radial arm saw

[[Has caption::power tool/saw| ]] [[MachineType::power tool/saw| ]]


A chop saw is an electric miter saw (BE: mitre saw) and consists of a large circular saw and a sturdy frame. Movement of the saw head is restricted by a sliding rail which can be angled both vertically and horizontally ("compound miter").

For the hand tool capable of making only horizontally angled cuts, see miter saw.

This tool needs some additional upgrades but is already usable for small workpieces.

Safety

Always keep your hands clear of the blade path and use the machine's clamp and the back fence to hold your workpiece in place. Before turning on the power at all, make sure you understand how the saw head will move and double check that all restraints are properly and tightly adjusted.

Blade

Our saw is designed for saw blades measuring 210 × 30 × 2.8 mm (OD × bore × thickness).

The currently installed blade is a "Craftomat" 210 × 30 × 2.5 mm one with 64 carbide-tipped teeth.

Noise & Dirt

If you are not alone, ask the others whether it is okay to cut for a few minutes as they may have to interrupt their project to give you room and to protect their ears. Although the saw is not extremely loud, it is definitely startling when you are surprised by it turning on in your back!

It's advisable to hook up a shop vac for dust extraction as the passive collector bags that typically come with this kind of tool are not too efficient. Even the shop vac will let a lot of sawdust escape.

Maintenance

The blade should be sharpened or replaced when it becomes dull, otherwise using it is very dangerous! Tell a manager if you are noticing any problems, e.g. increased force required to cut your workpieces or poor quality cuts.

Decreased cutting ability can also result from dirt buildup - here are some cleaning instructions.

Potential Upgrades

  • The work rests are crap and should be replaced by something, e.g. T-shaped wooden supports, at the proper height (see issue #11).
  • It's possible to create a "shadow line" indicating your cut location by carefully positioning an LED right above the blade. [1]
  • There is a clamping point on the right side of the blade, but when you actually put the clamp in there the motor will hit it. Could be fixed by adding a compatible hole (or simply another clamp) about 10 cm further to the right...very smart design -.-

Elektra Beckum KS 210 HM Plus

MachineInfoBox

Elektra Beckum KS 210 HM Plus

Machine-default.png
Synonyms: compound miter saw;
DE: Kappsäge, Kapp- und
Gehrungssäge
Type: [[power tool/saw]]
Material: wood
Used with: circular saw blades, shop vac
Location: commissioning shelf wood workshop
Access Requirements: Chop Saw Introduction
Status: [[Has InfoBox Status::in commissioning]]
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis
Sebastian
Jakob
Loewenstein
Similar (More or Less): miter saw, circular saw, table saw,
radial arm saw

[[Has caption::power tool/saw| ]] [[MachineType::power tool/saw| ]]


Martin brought in an alternative chop saw, which needs to be commissioned before it can be used.

If we can get it set up on the same height as the other one and with the fences in one line, both chop saws could be placed pretty close to each other!

This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task comment Status
Name the tool: Elektra Beckum KS 210 HM Plus done
Take a picture - pending
Find the manual as PDF needed for all machines - add a link to the InfoBox or comment where you could not find it pending
Documentation this page, status: in commissioning pending
Print QR-Code use the wikicrawler pending
Introduction - pending
Security Check to be done or witnessed by a manager pending
Test to be done or witnessed by a manager pending
tool's name, owner and approx. value provide to Patrick for inventorization pending
Last step: make it available physically and in the wiki - then delete this template pending