CNC Router

From CoMakingSpace Wiki
Revision as of 15:54, 25 November 2018 by Lukas (talk | contribs) (Materials: moving detailed content to "milling experiences"; replaced with general information)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
CNC router.gif

A CNC router is a computerized woodworking machine - basically a router mounted on a positioning system. While it may also be able to handle other materials than wood depending on the bits you use, a proper CNC mill is more precise for machining parts out of metals and other non-wood materials.

To use this machine, you need to familiarize yourself with at least two pieces of software:

There is also an interesting new approach of handheld CNC routing coming out which may remove the size constraints that come with any fixed-frame machine.


You can make furniture or even build a house. For more ideas, check out the CNC Milling Ideas.



Ooznest WorkBee CNC

Workbee frame.JPG
Synonyms: DE: CNC-Fräse, Portalfräsmaschine
Material: wood
Used with: 6 mm, 8 mm, 1/4" or 1/8" end mills;
some kinds of router bits
Location: CNC room
Access: upon introduction
Status: operational (please observe for any
problems due to the modifications)
Firmware: grbl
Software: LaserWeb, Fusion360, see G-Code Sender
Manual: product page, click "documentation" tab
Tutors: Patrick
Similar (More or Less): router, CNC mill

We built the 1500mm x 1500mm version of the WorkBee CNC, which is based on the Openbuilds OX. It can currently cut sheet material of up to 50 mm thickness on a work area of approximately 1250 × 1250 mm.

Details on setting it up can be found in issue #8 - maybe you would like to help?


The router mounted to it is a Dewalt D26200 (GB; known outside Europe as DWP611). You need to consider the sizes of its collets (Spannzangen) when buying your router bits.

  • no-load speed: 16000 - 27000 rpm
  • max cutter diameter: 30 mm
  • available collet diameters:
    • 6 mm
    • 8 mm
    • 1/4 inch (6.35 mm)
    • 1/8 inch (3.175 mm)

The collets of the DW613, DW620 and DW621 also fit the router and are easier to get in Germany than the original ones.


The spindle and the CNC controller + motors are hooked up to an electrical box on the left wall. You'll find a switch and an outlet for the spindle there. In case of an emergency the whole box can be shut off via one of the two emergency stops (inside the CNC room and on the outside above the access control). Everything except the Raspberry Pi will be turned off in that case.

Dust Extraction

We have added a cyclone dust separator between the shop vac and the CNC router itself. Thereby, the bulk of the shavings and dust should be collected in an easily emptied box rather than the shop vac's bag.

The part that attaches the dust extraction hose to the router is called a "dust shoe". We are currently using this one designed by Patrick. The next version should ideally fit the dust extraction hose without an adapter and include a kind of transparent, flexible "skirt" to optimize the airflow.

Other interesting designs:


This is just an overview and does NOT replace the personal introduction!

  1. create the tool paths in a suitable CAM software (e.g. Fusion 360)
  2. secure your workpiece on the machine's bed
  3. insert the appropriate collet & bit as defined in your tool paths
  4. turn the positioning motors on, home the machine and define the workpiece origin
  5. put on personal protection and turn the spindle on
  6. send the tool paths to the router in real time via the serial interface (USB)
    1. options can be found under "G-Code Senders"

Tips & Tricks

  • to avoid tear-out at the edge of a sensitive workpiece, it may be worthwhile to surround it with some sacrificial material (like MDF) before routing [1]


Ooznest recommends a 6mm spoiler board, our first one is 20mm thick. It is mounted to the frame using 4 drop-in T-slot nuts. Cutting into the boards will make it uneven, from time to time it is neccessary to surface the spoiler board again.

When there is time, we would like to drill workholding holes into the spoilboard.


(For more details, see "Milling Experiences")

CNC routing is most appropriate for non-metal panels/boards. The exact material might dictate your choice of endmill or router bit!

Cutting certain metals, e.g. millable aluminum, may still be possible with a lot of extra work, but a rigid and liquid-cooled CNC mill would be the proper way to go.

Helpful Links