CoMakingSpace Wiki - User Contributions [en]

Einhell BT-GW 150

2024-03-18T19:14:59Z

Meyerml:

MIG/MAG welding machine by Einhell.

To be used with Argon for [https://www.twi-global.com/technical-knowledge/job-knowledge/mig-welding-004 MIG] welding or CO2 for [https://www.uti.edu/blog/welding/gmaw-mag-welding MAG] welding.

{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|similar=https://wiki.comakingspace.de/Welding_Transformer|location=Metal Workshop|access=[[Introduction::Arc_Welding_Introduction]]|tutors=[[Tutor::User:Lukas|Lukas]]
[[Tutor::User:Johannes|Johannes]]
[[Tutor::User:Marcel|Marcel]]|manual=https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf}}{{Commissioning}}
[[File:Welding pressure gauge.jpg|thumb|The knobs and valves of the gas setup]]

== The gas setup ==
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate. Always turn the CO2 off after usage to reduce leakage losses.

== The welding machine ==
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg. If you swap in a wire of a different diameter, you must also change the contacting pipe (Kontaktrohr, see manual).[[File:BT-GW 150 Front.jpg|thumb|The settings of the machine]]Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the [https://wiki.comakingspace.de/Arc_Welding_Introduction2 welding introduction] on what else precautions you might need to take.

The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece.

Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker.

== Donation ==
The Argon gas costs 70 Euro per 20 l filling, which lasts about 350 minutes of welding (the cylinder holds ~ 4000 l of argon) this gives a cost of about 20 cents per minute of welding. The wire costs about 40 euro per kg, which leads to costs of another 20 cents per minute (at 5.4g/minute, assumed 3cm/s wire speed). Thus I would suggest a donation of 50 cents per minute of actual welding time.

== Suggested reading ==
Know the difference between the different [http://w welding methods]

[[Welding Area]]

[[Welding Helmet]]

TODO: update the welding area and metal workshop pages for the new welding machine.

Einhell BT-GW 150

2024-03-18T17:59:20Z

Meyerml:

MIG/MAG welding machine by Einhell.

To be used with Argon for [https://www.twi-global.com/technical-knowledge/job-knowledge/mig-welding-004 MIG] welding or CO2 for [https://www.uti.edu/blog/welding/gmaw-mag-welding MAG] welding.

{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|similar=https://wiki.comakingspace.de/Welding_Transformer|location=Metal Workshop|access=[[Introduction::Arc_Welding_Introduction]]|tutors=[[Tutor::User:Lukas|Lukas]]
[[Tutor::User:Johannes|Johannes]]
[[Tutor::User:Marcel|Marcel]]|manual=https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf}}{{Commissioning}}
[[File:Welding pressure gauge.jpg|thumb|The knobs and valves of the gas setup]]

== The gas setup ==
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate. Always turn the CO2 off after usage to reduce leakage losses.

== The welding machine ==
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg.[[File:BT-GW 150 Front.jpg|thumb|The settings of the machine]]Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the [https://wiki.comakingspace.de/Arc_Welding_Introduction2 welding introduction] on what else precautions you might need to take.

The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece.

Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker.

== Donation ==
The Argon gas costs 70 Euro per 20 l filling, which lasts about 350 minutes of welding (the cylinder holds ~ 4000 l of argon) this gives a cost of about 20 cents per minute of welding. The wire costs about 40 euro per kg, which leads to costs of another 20 cents per minute (at 5.4g/minute, assumed 3cm/s wire speed). Thus I would suggest a donation of 50 cents per minute of actual welding time.

== Suggested reading ==
Know the difference between the different [http://w welding methods]

[[Welding Area]]

[[Welding Helmet]]

TODO: update the welding area and metal workshop pages for the new welding machine.

Einhell BT-GW 150

2024-03-18T17:52:06Z

Meyerml:

MIG/MAG welding machine by Einhell.

To be used with Argon for [https://www.twi-global.com/technical-knowledge/job-knowledge/mig-welding-004 MIG] welding or CO2 for [https://www.uti.edu/blog/welding/gmaw-mag-welding MAG] welding.

{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|similar=https://wiki.comakingspace.de/Welding_Transformer|location=Metal Workshop|access=[[Introduction::Arc_Welding_Introduction]]|tutors=[[Tutor::User:Lukas|Lukas]]
[[Tutor::User:Johannes|Johannes]]
[[Tutor::User:Marcel|Marcel]]|manual=https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf}}{{Commissioning}}
[[File:Welding pressure gauge.jpg|thumb|The knobs and valves of the gas setup]]

== The gas setup ==
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate. Always turn the CO2 off after usage to reduce leakage losses.

== The welding machine ==
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg.[[File:BT-GW 150 Front.jpg|thumb|The settings of the machine]]Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the [https://wiki.comakingspace.de/Arc_Welding_Introduction2 welding introduction] on what else precautions you might need to take.

The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece.

Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker.

== Donation ==
The Argon gas costs 70 Euro per filling, which lasts about 350 minutes of welding (the cylinder holds ~ 4000 l of argon) this gives a cost of about 20 cents per minute of welding. The wire costs about 40 euro per kg, which leads to costs of another 20 cents per minute (at 5.4g/minute, assumed 3cm/s wire speed). Thus I would suggest a donation of 50 cents per minute of actual welding time

== Suggested reading ==
Know the difference between the different [http://w welding methods]

Einhell BT-GW 150

2024-03-18T17:23:52Z

Meyerml:

MIG/MAG welding machine by Einhell.

To be used with Argon for [https://www.twi-global.com/technical-knowledge/job-knowledge/mig-welding-004 MIG] welding or CO2 for [https://www.uti.edu/blog/welding/gmaw-mag-welding MAG] welding.

{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|similar=https://wiki.comakingspace.de/Welding_Transformer|location=Metal Workshop|access=[[Introduction::Arc_Welding_Introduction]]|manual=https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf}}{{Commissioning}}
[[File:Welding pressure gauge.jpg|thumb]]

== The gas setup ==
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate.

== The welding machine ==
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg.

Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the [https://wiki.comakingspace.de/Arc_Welding_Introduction2 welding introduction] on what else precautions you might need to take.

The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece.

Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker.

== Suggested reading ==
Know the difference between the different [http://w welding methods]

[[File:BT-GW 150 Front.jpg|thumb|THe settings of the machine]]

Arc Welding Introduction2

2024-03-18T16:46:17Z

Meyerml: threw out everything related to electrode welding

This is the content required for an introduction to our [[Einhell BT-GW 150|inert gas welding machine]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)

If you need this Introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Marcel|Marcel]], [[Tutor::User:Johannes|Johannes]]

Let's begin! First off, make sure you have read the machine's [[Einhell BT-GW 150|wiki page]].

== Safety ==
[[PPE|Personal protection]]: [[File:Protection - welding mask.svg|50px]] [[File:Protection - gloves.svg|50px]] [[File:protection - protective clothing.svg|50px]]

:Make sure you cover yourself completely, there should be no exposed skin at all!
:*[[Welding Jacket|welding jacket]]
:* [[Welding Gloves|welding gloves]] over the jacket
:* ideally also a fireproof apron against molten metal drops and as additional radiation protection
:* robust shoes against glowing hot beads: sandals or sports shoes with mesh top do not provide sufficient cover

:'''Protect your eyes''' with a '''properly adjusted''' [[Welding Helmet|welding helmet]] during welding, and at least [[goggles]] when inspecting the weld or [[Slag Hammer|hammering]] & brushing off slag (it may be easiest to just wear goggles under the helmet so you can't forget them!)

{| class="wikitable"
|-
! Dangers !! Precautions
|-
| [[File:danger - optical radiation.svg|50px]] CRITICAL HAZARD - extremely bright arc
* light damages eyes, risks include permanent blindness if used without appropriate protection
* UV radiation burns exposed skin
||
* wear proper [[PPE|personal protection]] (see above)
* immediately stop if '''anything''' seems to be wrong with the welding helmet
|-
| [[File:danger - heat.svg|50px]] extreme heat
* splattering molten metal
*workpiece heats up a lot
*welding gun, and wire also heat up
||
* make sure there are no gaps in your [[PPE|personal protection]], e.g. between pants and shoes or jacket and gloves
* wear only cotton clothing - synthetics could melt to your body
* do NOT touch hot stuff, even welding gloves just tolerate so much heat (don't ruin them) so use pliers to manipulate your workpieces if you have to
|-
|fire hazard

* Sparks can ignite combustible material
* workpiece can reach auto ignition temperature of its coating or residues
* welding gun is hot after welding and might ignite stuff
|
* remove all easily combustible materials from your work area
* make sure your workpiece is clean
* know where the nearest [[Fire Extinguisher|fire extinguisher]] is located
|-
| toxic fumes (e.g. ozone, flux components, nitrous gases, heavy metal particles)
* galvanized steel ''(verzinkter Stahl)'' releases zinc oxide when welded which can give you "metal fume fever" [https://www.metalsupermarkets.com/welding-galvanized-steel/]
* stainless steel releases hexavalent chromium (carcinogenic)
* other coatings may also release all sorts of unknown compounds when vaporized
||
* [[grind]] away '''any''' surface coatings (e.g. galvanization, paint) before welding, they could generate harmful fumes or at least obstruct your weld
* take care of good ventilation - Use BOTH exhausts of the [[Welding Area|welding enclosure]]; but even that might not be enough for long sessions or difficult materials! Also, you should obviously avoid breathing in the fumes.
* "If the air in your breathing zone is not clear, or if breathing is uncomfortable, check to be sure the ventilation equipment is working and report concerns to a supervisor" [https://www.lincolnelectric.com/en-us/support/welding-solutions/Pages/Five-potential-welding-safety-hazards.aspx]
*stop immediately if you are experiencing nausea and report the incident to a supervisor
|-
| [[File:danger - high voltage.svg|50px]] exposed electricity (up to 60 V DC, 100+ A)
* still below ''zulässige Berührungsspannung'' - minor risk of shock
* equipment may overheat
|| reduce the chances of electric accidents: [https://www.bghm.de/fileadmin/user_upload/Arbeitsschuetzer/Gesetze_Vorschriften/Informationen/209_010.pdf]
* make sure you are isolated (proper dry gloves, shoes and/or floor mat) from the workpiece, especially do not touch the electrode and the workpiece simultaneously
* unplug the welding machine when not in use
* if you use a cable drum, make sure to unwind it completely - a wound cable drum will induce current and heat up the cables, which may lead to a molten cable coat with high risk of a exposed mains wire
* in case of electric shock, always make sure to visit a doctor!
|-
| always turn off the inert gas after use, as leakage accurs ||
|}

== Suggested Reading ==
These websites may also be interesting:
* ''[https://www.bghm.de/arbeitsschuetzer/fachinformationen/schweissen-und-verwandte-verfahren/ BGHM: Schweißen und verwandte Verfahren (DE)]'' - detailed safety information
* ''[https://www.bghm.de/arbeitsschuetzer/praxishilfen/arbeitsschutz-kompakt/033-lichtbogenhandschweissen/ BGHM: Arbeitsschutz kompakt - Lichtbogenhandschweißen (DE)]'' - nice short safety overview, "checklist" style
* [https://www.lincolnelectric.com/en-us/support/welding-solutions/Pages/Five-potential-welding-safety-hazards.aspx five potentioal welding safety hazards]

== Demonstration ==
The tutor will show you these steps in detail:
* check [[Welding Helmets|welding helmet]] settings
* set up your work in the welding enclosure
** what way to enter best
** close gaps, e.g. with spring clamps (long-term solution needed!)
** bring a light with you, if necessary
* turn on the BOTH exhaust systems
**The trunk only ramps up to high if you temporarily obstruct the airflow
*try striking an arc and depositing metal on a scrap piece (e.g. in the shape of your initials)
** it's good to experience the often scary sensation of your first arc ignition with your tutor ;-)
** once there is a steady arc, push forward and make little circles in the weld pool to "mix" the workpiece(s) with the deposited material

Staplers

2023-11-08T10:43:08Z

Meyerml:

{{wanted}}

== Office Staplers ==
{{ToolInfoBox
|tool name=Office Staplers
|image=Office_staplers.jpg
|synonyms=DE: Heftgerät, "Tacker"
|type=office hand tool
|access=
|location=
|material=[[paper]]
}}
Office staplers are most commonly used to bind stacks of paper with [[staples]] that are driven through by punching the lever and bent around by a small "anvil" on the tool's foot.

Waiting Lists

2023-04-26T16:31:46Z

Meyerml: added my name

An overview of the waiting lists for our [[introductions]] that take more time than the [[tutors]] can usually invest spontaneously.

''If you want to "wait" for a vehicle spot, see [[Vehicle Workspaces|vehicle workspaces]].''

<big>'''How to Use'''</big> 
Please '''link''' your [[Special:MyPage|user page]] at the bottom of each list you're interested in after you've filled it with enough information to contact you and/or activated "Allow other users to email me" in your [[Special:Preferences|preferences]]!

If a list is full enough and/or you have been waiting for a while, please reach out to the tool's tutors and kindly ask for a date - maybe they've just been too busy, but it could also be that they missed the list filling up and would appreciate the reminder.

==[[3D Printer Introduction]] ==

Tutors:{{#show: 3D Printer Introduction
|?Tutor
| format=ul
}}
Time required: ~1h

Next Date: TBD

'''Waiting Members:'''

* [[User:Ed Green|Ed]]
*[[User:Solich|Martin S.]]
*[[User:WalzPh|Philipp]]
*[[User:Beornius|Stefano]]
*[[Ol|Oliver]]
*[[User:Nora|Nora]]
*

==[[Arc Welding Introduction]]==

Tutors: {{#show: Arc Welding Introduction
|?Tutor
| format=ul
}}
Time required: 1 h + 20 min per member (to be confirmed)

Next Date: TBD - waiting for completion of the welding corner, [https://github.com/comakingspace/do-something/issues/199 everyone can help!]

'''Waiting Members:'''

* [[User:Mitja|Mitja]]
* [[User:Blacksheep|Micha]]
* [[User:Christoph|Christoph]]
* [[User:Mfisch3r|Markus]]
* [[User:AlexBaumgart|AlexBaumgart]]
* [[User:Andreas|Andreas]]
* [[User:Utis|Utis]]
*[[User:Diemex|Diemex]]
*[[User:BenKenobi|Benedict]]
*[[User:SvenG|SvenG]]
*[[User:Björn|Björn]]
*[[User:Tom|Tom]]
*[[User:Neo|Neo]]
*[[User:Koen|Koen]]
*[[User:Kvidberg|Kvidberg]]
*[[User:Ol|Oliver]]
*[[User:Meyerml|marcel meyer]]

==[[Bandsaw Introduction]]==

Tutors: {{#show: Bandsaw Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1.5 h

Next Date: 2023-4-26, 20:30

'''Waiting Members:'''
* [[User:Utis|Utis]]
* [[User:Olli.Klos|Olli Klos]]
*[[User:Jrosy|Jrosy]]
*[[User:Björn|Björn]]
*[[User:Neo|Neo]]
*[[User:Jakob|Jakob]]
*[[Nils Buchenau]]
*[[User:Koen|Koen]]
*[[User:WalzPh|Philipp]]
*[[User:Kvidberg|Kvidberg]]
*[[User:Beornius|Stefano]]
*[[User:Ol|Oliver]]
*[[User:Nora|Nora]]
*[[User:Mario|Mario]]
*[[User:Marcel|Marcel]]

== [[Chop Saw Introduction]] ==
Tutors: {{#show: Chop Saw Introduction
|?Tutor
| format=ul
}}

Time required: ~30 min

Next Date: TBD

'''Waiting Members:'''

* [[User:SvenG|SvenG]]
*[[User:Neo|Neo]]
*[[User:Draco|Draco]]
*[[User:Ol|Oliver]]

== [[CNC Mill Introduction]] ==

Tutors: {{#show: CNC Mill Introduction
|?Tutor
| format=ul
}}
Time required: > 1 h (to be confirmed)

Next Date: TBD

'''Waiting Members:'''
* [[User:Trix|Trix]]
*[[User:Jakob|Jakob]]
*[[User:Ol|Oliver]]
*[[User:Meyerml|marcel meyer]]

== [[CNC Router Introduction]] ==

Tutors: {{#show: CNC Router Introduction
|?Tutor
| format=ul
}}
Time required: > 1 h (to be confirmed)

Next Date: TBD

'''Waiting Members:'''

*[[User:Leo|Leo]]
* [[User:Ed_Green|Ed_Green]]
* [[User:Olli.Klos|Olli Klos]]
*[[User:Lepus|Nidal]]
*[[User:Jrosy|Jrosy]]
*[[LaVo]]
*[[User:Koen|Koen]]
*[[User:FabianM|Fabian]]
*[[User:WalzPh|Philipp]]
*[[User:Loewenstein|Jan]]
*[[User:Trix|Trix]]
*[[User:Kvidberg]]
*[[User:Jnohl|Jnohl]]
*[[User:Beornius|Stefano]]
*[[User:Ol|Oliver]]
*[[User:Meyerml|marcel meyer]]
*

== [[Handheld Router Introduction]] ==

Tutors: {{#show: Handheld Router Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1 h + 15 min per member

Next Date: TBD

'''Waiting Members:'''

* [[User:Utis|Utis]]
*[[User:Solich|Martin S.]]
* [[User:Heidleberg trashure|Irina F.]]
*[[Trix]]
*[[User:Nora|Nora]]

== [[Jointer-Planer Introduction]] ==
Tutors: {{#show: Jointer-Planer Introduction
|?Tutor
| format=ul
}}

Time required: 60 min + 15 min per member

Next Date: TBD

'''Waiting Members:'''
* [[User:Utis|Utis]]
*[[User:Jrosy|Jrosy]]
*[[User:Solich|Martin S.]]
*[[User:Neo|Neo]]
*[[User:Jakob|Jakob]]
*[[User:Koen|Koen]]
*[[User:FabianM|Fabian]]
*[[User:Kvidberg|Kvidberg]]
*[[Anitamareike]]
*[[User:Beornius|Stefano]]
*[[User:Ol|Oliver]]
*[[User:Nora|Nora]]
*[[User:Mario|Mario]]
*[[User:Marcel|Marcel]]
*[[User:Meyerml|marcel meyer]]

== [[Laser Cutter Introduction]] ==

Tutors: {{#show: Laser Cutter Introduction
|?Tutor
| format=ul
}}
Time required: ~2h

Next Date: TBD

'''Waiting Members:'''

*[[User:Olli.Klos|Olli Klos]]
* [[User:Christoph|Christoph]]
*[[User:Woodkid|Lukas Mathur]]
*[[User:Koen|Koen]]
*[[User:FabianM|Fabian]]
*[[User:Loewenstein|Jan]]
*[[User:Draco|Draco]]
*[[User:Kvidberg|Kvidberg]]
*[[User:Jnohl|Jnohl]]
*[[User:Ol|Oliver]]

== [[Metal Lathe Introduction]] ==
Tutors: {{#show: Metal Lathe Introduction
|?Tutor
| format=ul
}}

Time Required: 2-3h

Next Date: TBD

'''Waiting Members:'''

* [[User:ErikSchatz|Erik]]
* [[User:BenKenobi|Benedict]]
*[[User:Koen|Koen]]
*[[User:Kvidberg|Kvidberg]]
*[[User:Meyerml|marcel meyer]]

== [[Table Saw Introduction]] ==
Tutors: {{#show: Table Saw Introduction
|?Tutor
| format=ul
}}

Time required: ~ 1 h

Next Date:

'''Waiting Members:'''

* [[User:Ozel|Oliver]]
*[[User:Draco|Draco]] (no response to March 2023 invitation)
*[[User:Kvidberg|Kvidberg]] (no response to March 2023 invitation)

==[[Woodturning Introduction]]==

Tutors: {{#show: Woodturning Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1 h + 20 min per person

Next Date: TBD

'''Waiting Members:'''

* [[User:Olli.Klos|Olli Klos]]
* [[User:Johanna|Johanna]]
* [[User:Ronanb|Ronan]]
*[[User:Koen|Koen]]
*[[User:FabianM|Fabian]]
*[[User:Kvidberg|Kvidberg]]
*[[Anitamareike]]
*[[User:Ol|Oliver]]

Waiting Lists

2022-11-04T11:20:51Z

Meyerml: /* 3D Printer Introduction */

An overview of the waiting lists for our [[introductions]] that take more time than the [[tutors]] can usually invest spontaneously.

''If you want to "wait" for a vehicle spot, see [[Vehicle Workspaces|vehicle workspaces]].''

<big>'''How to Use'''</big> 
Please '''link''' your [[Special:MyPage|user page]] at the bottom of each list you're interested in after you've filled it with enough information to contact you and/or activated "Allow other users to email me" in your [[Special:Preferences|preferences]]!

If a list is full enough and/or you have been waiting for a while, please reach out to the tool's tutors and kindly ask for a date - maybe they've just been too busy, but it could also be that they missed the list filling up and would appreciate the reminder.

==[[3D Printer Introduction]] ==

Tutors:{{#show: 3D Printer Introduction
|?Tutor
| format=ul
}}
Time required: ~1h

Next Date: TBD

'''Waiting Members:'''

* [[User:Ed Green|Ed]]
*[[User:Paul|Paul G.]]
*[[User:Solich|Martin S.]]
*[[User:Meyerml|Marcel M.]]
*[[User:Tom|Tom]]
*

==[[Arc Welding Introduction]]==

Tutors: {{#show: Arc Welding Introduction
|?Tutor
| format=ul
}}
Time required: 1 h + 20 min per member (to be confirmed)

Next Date: TBD - waiting for completion of the welding corner, [https://github.com/comakingspace/do-something/issues/199 everyone can help!]

'''Waiting Members:'''

* [[User:Mitja|Mitja]]
* [[User:Blacksheep|Micha]]
* [[User:Christoph|Christoph]]
* [[User:Mfisch3r|Markus]]
* [[User:AlexBaumgart|AlexBaumgart]]
* [[User:Andreas|Andreas]]
* [[User:PaulW|PaulW]]
* [[User:Utis|Utis]]
*[[User:Diemex|Diemex]]
*[[User:BenKenobi|Benedict]]
*[[User:SvenG|SvenG]]
*[[User:Björn|Björn]]
*[[User:Tom|Tom]]

==[[Bandsaw Introduction]]==

Tutors: {{#show: Bandsaw Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1.5 h

Next Date: 2022-3-5 (sign up [https://www.termino.gv.at/meet/b/c3f3642b86b533b6c03a9d8173904b06-114282 here])

'''Waiting Members:'''
* [[User:PloenK|PloenK]]
* [[User:Utis|Utis]]
* [[User:Olli.Klos|Olli Klos]]
*[[User:Jrosy|Jrosy]]
* [[User:Heidleberg trashure|Irina F.]]
*[[User:Björn|Björn]]
*[[User:Mieko|Mieko]]

== [[Chop Saw Introduction]] ==
Tutors: {{#show: Chop Saw Introduction
|?Tutor
| format=ul
}}

Time required: ~30 min

Next Date: 2022-3-5 (sign up [https://www.termino.gv.at/meet/b/c3f3642b86b533b6c03a9d8173904b06-114282 here])

'''Waiting Members:'''

* [[User:SvenG|SvenG]]
*[[User:FelixB|FelixB]]
*[[User:Tom|Tom]]

== [[CNC Router Introduction]] ==

Tutors: {{#show: CNC Router Introduction
|?Tutor
| format=ul
}}
Time required: > 1 h (to be confirmed)

Next Date: 2022-3-5 (sign up [https://www.termino.gv.at/meet/b/c3f3642b86b533b6c03a9d8173904b06-114282 here])

'''Waiting Members:'''

*[[User:Leo|Leo]]
* [[User:Ed_Green|Ed_Green]]
* [[User:Olli.Klos|Olli Klos]]
* [[User:Lars|Lars]]
* [[User:Christoph|Christoph]]
*[[User:Lepus|Nidal]]
*[[User:Jrosy|Jrosy]]
*[[LaVo]]
*[[User:Tom|Tom]]

== [[Handheld Router Introduction]] ==

Tutors: {{#show: Handheld Router Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1 h + 15 min per member

Next Date: TBD

'''Waiting Members:'''

* [[User:BenKenobi|BenKenobi]]
* [[User:Utis|Utis]]
*[[User:Jrosy|Jrosy]]
*[[User:Paul|Paul G.]]
*[[User:Solich|Martin S.]]
* [[User:Heidleberg trashure|Irina F.]]
*[[User:Tom|Tom]]

== [[Jointer-Planer Introduction]] ==
Tutors: {{#show: Jointer-Planer Introduction
|?Tutor
| format=ul
}}

Time required: 60 min + 15 min per member

Next Date: Wed, 2022-11-2, 19:00

'''Waiting Members:'''

*[[User:Jrosy|Jrosy]]
*[[User:Solich|Martin S.]]
*[[User:Tom|Tom]]
* [[User:Eileen|Eileen]]
* [[User:Utis|Utis]]

== [[Laser Cutter Introduction]] ==

Tutors: {{#show: Laser Cutter Introduction
|?Tutor
| format=ul
}}
Time required: ~2h

Next Date: 2022-3-5 (sign up [https://www.termino.gv.at/meet/b/c3f3642b86b533b6c03a9d8173904b06-114282 here])

'''Waiting Members:'''

*[[User:Olli.Klos|Olli Klos]]
* [[User:Christoph|Christoph]]
*
*[[Stefanr|User:Stefanr]]
*[[User:Tom|Tom]]
*[[User:Woodkid|Lukas Mathur]]

== [[Metal Lathe Introduction]] ==
Tutors: {{#show: Metal Lathe Introduction
|?Tutor
| format=ul
}}

Time Required: 2-3h

Next Date: TBD

'''Waiting Members:'''

* [[User:ErikSchatz|Erik]]
* [[User:BenKenobi|Benedict]]
* [[User:Sebastian|Sebastian]]
*[[User:Tom|Tom]]

== [[Table Saw Introduction]] ==
Tutors: {{#show: Table Saw Introduction
|?Tutor
| format=ul
}}

Time required: ~ 1 h

Next Date: 2022-2-23, 19:00 (ask [[Keno]] about open slots!)

'''Waiting Members:'''

* [[User:Ozel|Oliver]]
* [[User:Diemex|Max]]
* [[User:PipoNunesV|Filipe]]
* [[User:Heidleberg trashure|Irina F.]]
*[[User:Mieko|Mieko]]
*[[Lasse]]

==[[Woodturning Introduction]]==

Tutors: {{#show: Woodturning Introduction
|?Tutor
| format=ul
}}
Time required: ~ 1 h + 20 min per person

Next Date: ''TBD'' (last: 2021-11-20)

'''Waiting Members:'''

* [[User:Olli.Klos|Olli Klos]]
* [[User:Sebastian|Sebastian]]
* [[User:Ronanb|Ronan]]
*[[User:Jrosy|Jrosy]]
*[[User:Björn|Björn]]
*[[User:Mieko|Mieko]]

User:Meyerml

2022-11-04T11:11:46Z

Meyerml:

Hi,

Ich bin seit November 2022 Mitglied und bastel gerne mit Arduinos/ESP Microcontrollern.

Außerdem baue ich gerne Lampen aus allen möglichen Dingen.

richtiger Name: Marcel Meyer

User:Meyerml

2022-11-04T11:11:13Z

Meyerml: introduction

Hi,

Ich bin seit November 2022 Mitglied und bastel gerne mit Arduinos/ESP Microcontrollern.

Außerdem baue ich gerne Lampen aus allen möglichen Dingen.

Meyerml

2022-11-04T11:07:26Z

Meyerml: created redirect for user page

#REDIRECT [[User:Meyerml]]

User:Meyerml

2022-11-04T11:07:26Z

Meyerml: create user page