CoMakingSpace Wiki - User Contributions [en]

Vertical Bandsaw Introduction

2018-07-19T12:59:05Z

Khaos8rood:

{{incomplete}}

This is the content required for an introduction to our <[[Bandsaws]]> - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)

Let's begin! First off, make sure you have read the machine's <MANUAL>.

== Safety ==
=== Dangers ===
'''ENTANGLEMENT HAZARD!''' '''NEVER''' use without instaled saveguard. '''DO NOT''' use close by flameable liquides and/or gas. '''DO NOT''' modify the machine on your own authority (insurance, you know). Befor servicing, adjusting or cleaning the machine '''ALWAYS''' turn Power OFF and wait for the blade to grind to a halt. '''ALWAYS''' keep bandsaw-blades in safe custody. '''SPECIAL CAUTION''' when working with toxic woods (like; ''Eiche, Esche, Eibe, Buche, Buchsbaum''). small splinters can fly towards the operator

=== Precautions ===
Alway wear: '''Tight clothing, Safty googles, Ear protection''', when working with heavier workpieces, - '''safty-boots''' and especialy while working with toxic woods, - '''dust mask'''.

-Keep your workspace decent and clean and your footroom free of obstacles. -Check bandsaw for foreign particles. -Check bandsaw-blade for cracks and that saw teeth are looking downwards. -Adjust blade: tensioning the blade by turning the tighting-screw. The numbers on the chart shows the width of the blade (the thicker the blade the tighter the tension, what a sentence...). Observe if the blade is lying in the middle of the pulley. Adjust blade-guide: Guide-pins should touch, not press, the blade but should'nt touch the saw-teeth. Leaf an 0,5-1mm gap to the back roller. Repeat this with the lower guide-unit. -Lower the blade guard as close as possible down to the workpiece. -Hold ready the parallel fence, push stick and a jig/wedge when sawing round workpieces

== Suggested Reading ==
Besides these safety notes, you should read <...>

== Demonstration ==
The tutor will show you these steps in detail:
* <...>

[[Category:Introductions]]

Talk:Vertical Bandsaw Introduction

2018-07-19T12:10:24Z

Khaos8rood:

''Die Skala an der Metabo für die Sägeband-Spannung gibt vermutlich direkt die dicke des Sägebandes an. Es sollte also geprüft werden was auf unsere
Bänder zutrifft und die in der Manual angeben.''

Talk:Vertical Bandsaw Introduction

2018-07-19T12:09:28Z

Khaos8rood:

Die Skala an der Metabo für die Sägeband-Spannung gibt vermutlich direkt die dicke des Sägebandes an. Es sollte also geprüft werden was auf unsere
Bänder zutrifft und die in der Manual angeben.

Talk:Vertical Bandsaw Introduction

2018-07-19T12:09:08Z

Khaos8rood: Created page with "Die Skala an der Metabo für die Sägeband-Spannung gibt vermutlich die dicke des Sägebandes an. Es sollte also geprüft werden was auf unsere Bänder zutrifft und die in de..."

Die Skala an der Metabo für die Sägeband-Spannung gibt vermutlich die dicke des Sägebandes an. Es sollte also geprüft werden was auf unsere
Bänder zutrifft und die in der Manual angeben.

Vertical Bandsaw Introduction

2018-07-19T12:05:59Z

Khaos8rood:

{{incomplete}}

This is the content required for an introduction to our <[[Bandsaws]]> - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)

Let's begin! First off, make sure you have read the machine's <MANUAL>.

== Safety ==
=== Dangers ===
'''ENTANGLEMENT HAZARD!''' '''NEVER''' use without instaled saveguard. '''DO NOT''' use close by flameable liquides and/or gas. '''DO NOT''' modify the machine on your own authority (insurance, you know). Befor servicing, adjusting or cleaning the machine '''ALWAYS''' wait for the blade to grind to a halt. '''ALWAYS''' keep bandsaw-blades in safe custody. '''SPECIAL CAUTION''' when working with toxic woods (like; ''Eiche, Esche, Eibe, Buche, Buchsbaum''). small splinters can fly towards the operator

=== Precautions ===
Alway wear: '''Tight clothing, Safty googles, Ear protection''', when working with heavier workpieces, - '''safty-boots''' and especialy while working with toxic woods, - '''dust mask'''.

-Keep your workspace decent and clean and your footroom free of obstacles. -Check bandsaw for foreign particles. -Check bandsaw-blade for cracks and that saw teeth are looking downwards. -Adjust blade: tensioning the blade by turning the tighting-screw on top of the bandsaw. The numbers on the chart shows the width of the blade (the thicker the blade the tighter the tension, what a sentence...).

== Suggested Reading ==
Besides these safety notes, you should read <...>

== Demonstration ==
The tutor will show you these steps in detail:
* <...>

[[Category:Introductions]]

Vertical Bandsaw Introduction

2018-07-18T12:07:20Z

Khaos8rood:

Vertical Bandsaw Introduction

2018-07-18T11:56:14Z

Khaos8rood:

Vertical Bandsaw Introduction

2018-07-18T11:54:47Z

Khaos8rood:

{{incomplete}}

This is the content required for an introduction to our <Bandsaw> - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)

Let's begin! First off, make sure you have read the machine's <MANUAL>.

== Safety ==
=== Dangers ===
'''ENTANGLEMENT HAZARD!''' '''NEVER''' use without instaled saveguard. '''DO NOT''' use close by flameable liquides and/or gas. '''DO NOT''' modify the machine on your own authority (insurance, you know). Befor servicing, adjusting or cleaning the machine '''ALWAYS''' wait for the blade to grind to a halt. '''ALWAYS''' keep bandsaw-blades in safe custody. '''SPECIAL CAUTION''' when working with toxic woods (like; ''Eiche, Esche, Eibe, Buche, Buchsbaum''). 

=== Precautions ===
Alway wear: '''Tight clothing, Safty googles, Ear protection''', when working with heavier workpieces, - '''safty-boots''' and especialy while working with toxic woods, - '''dust mask'''.

== Suggested Reading ==
Besides these safety notes, you should read <...>

== Demonstration ==
The tutor will show you these steps in detail:
* <...>

[[Category:Introductions]]

User:Khaos8rood

2018-07-18T11:14:13Z

Khaos8rood: Created page with "==Hi there== Its simply an Aris. Brood in chaos, born in creative ecstasy and brought to self-reorganizing life to finaly bring chaos again over useless structures for there..."

==Hi there==

Its simply an Aris. Brood in chaos, born in creative ecstasy and brought to self-reorganizing life to finaly bring chaos again over useless structures for there will be more Space to Co-Make it anew. . . Damn!

Laser Printers

2018-06-18T17:13:58Z

Khaos8rood: /* HP LaserJet 8150DN */

== HP LaserJet 8150DN ==
{{MachineInfoBox
|machine name=HP LaserJet 8150DN
|image=HP LaserJet 8150DN.JPG
|synonyms=DE: Laserdrucker
|type=[[Print Media|print media]] device
|material=[[paper]], toner
|location=[[Common Room|common room]]
|access=upon reading
|status=
|firmware=
|software=
|manual=
|tutors=
|used with=[[computers]]
|similar=[[Inkjet Printers|inkjet printers]]
}}
If you want to install the printer to use it with your laptop, follow the steps below.

https://support.hp.com/us-en/drivers/selfservice/hp-laserjet-8150-printer-series/27718/model/21691

[[File:Installation 2D Drucker 8150DN.png]]

If you're the last one leaving the making space turn off the lights and shut down the laser printer.
You can find the button left beside the drawer number 3. Just push the button!

 

== HP LaserJet P1102w ==
[[User:Moritz|Moritz]] also brought in a used black-and-white laser printer that has some flaws but should still be great for printing templates!

known issues:
* the rolls wrinkle the paper (too tight?)
* the toner leaves smears along the length of the page

Maybe one or both of these problems can be fixed - more information on the device to follow!

[[Category:Print Media]]